Re: A89: Re: 'Remote Mode'
[Prev][Next][Index][Thread]
Re: A89: Re: 'Remote Mode'
Well, when I was in remote mode on my 89, and I tried to type the same key
sequence in again, it didn't do anything. And it never shut off after about
20 minutes.
Bryan
----- Original Message -----
From: Jeff Tyrrill <jeff_tyrrill@msn.com>
To: <assembly-89@lists.ticalc.org>
Sent: Thursday, August 12, 1999 5:57 PM
Subject: RE: A89: Re: 'Remote Mode'
>
> Yes, exactly. When you "enable" remote mode again, remote mode will
actually
> be completely off. If you "enable" it again and it turns on again, that
> means the TI-89 works differently than the TI-92. In that case, just APD
or
> take out one battery and it will be off.
>
> -----Original Message-----
> From: owner-assembly-89@lists.ticalc.org
> [mailto:owner-assembly-89@lists.ticalc.org]On Behalf Of Bryan Rabeler
> Sent: Thursday, August 12, 1999 10:25 AM
> To: assembly-89@lists.ticalc.org
> Subject: Re: A89: Re: 'Remote Mode'
>
>
>
> You mean I am supposed to enable remote mode again, and that will in fact
> actually disable remote mode?
>
> Bryan
>
> ----- Original Message -----
> From: Jeff Tyrrill <jeff_tyrrill@msn.com>
> To: <assembly-89@lists.ticalc.org>
> Sent: Thursday, August 12, 1999 4:04 AM
> Subject: RE: A89: Re: 'Remote Mode'
>
>
> >
> > On the original TI-92, the calc was unstable after apparently being
taken
> > out of remote mode by taking a battery out, because it is still sending
> > output to the link port, just not waiting for input from the link port.
> > Anything that causes the calc to run out of memory and give a TI-Basic
> > Error: Memory will instead just crash the calc. Perform the procedure to
> > enable remote mode again in order to disable it completely and
> re-stabilize
> > the calc. This is according to David Ellsworth's ti-bugs.doc file. Also,
> my
> > TI-92 didn't APD when it was in remote mode.
> >
> > -----Original Message-----
> > From: owner-assembly-89@lists.ticalc.org
> > [mailto:owner-assembly-89@lists.ticalc.org]On Behalf Of Bryan Rabeler
> > Sent: Monday, August 09, 1999 5:43 PM
> > To: assembly-89@lists.ticalc.org
> > Subject: Re: A89: Re: 'Remote Mode'
> >
> >
> >
> > Well, after leaving my 89 on for another 10 minutes, I decided to take a
> > battery out. After I turned the calculator back on, it was out of
remote
> > mode and my programs were still there...
> >
> > Bryan
> >
> > ----- Original Message -----
> > From: Bryan Rabeler <rabelerb@pilot.msu.edu>
> > To: <assembly-89@lists.ticalc.org>
> > Sent: Monday, August 09, 1999 6:11 PM
> > Subject: Re: A89: Re: 'Remote Mode'
> >
> >
> > >
> > > How long does it take for the APD to set in? My 89 has been idle for
> more
> > > than 10 minutes, and its still on..
> > >
> > > Bryan
> > >
> > > ----- Original Message -----
> > > From: <AzNgUy66@aol.com>
> > > To: <assembly-89@lists.ticalc.org>
> > > Sent: Monday, August 09, 1999 5:41 PM
> > > Subject: Re: A89: Re: 'Remote Mode'
> > >
> > >
> > > >
> > > > you get out of remote mode by just leaving it on until the apd turns
> off
> > > the
> > > > calc.... then you turn the calc back on and it is out of remote mode
> > > >
> > > > =]
> > > >
> > > >
> > >
> > >
> > >
> >
> >
> >
> >
> >
> >
>
>
>
>
>
>
Follow-Ups:
References: