Re: TI-H: Backlight
[Prev][Next][Index][Thread]
Re: TI-H: Backlight
I have found a better way to do the backlight. The only problem is it
costs $95.00 and it HAS to have an external power supply. It has to
because it needs an inverter to use DC power. I forget the name of the
company right now, when I remember I will post. To install the thing is
really simple though. You just pull the gray "mirror" from your screen
and put place this screen behind your LCD. It sticks using that static
kinda thing.
Gregory
Richard Piotter wrote:
>
> Hi!
>
> I want to post it, but time and work have prevented me from even
> updating the battery expander page. I took a Sharp LM64P something
> backlit monochrome LCD apart. It is 640x480 pixsels, and the
> diffratction panel is really good. Lights the whole screen if cut right!
> I don't guarantee your screen will work WELL with it, but I do guarantee
> it will light it up. The screen lights fine. The problem comes in with
> some newer screens (maybe it's newer screens, but I'm not sure). The
> problem is that to properly install the backlight, you need to cut the
> rubber that holds the screen off and then peel the mirror off. You put
> the mirror on the back (rough) side of the difractor and put a diffuser
> on top, then the LCD. The problem is that some screens use the mirror
> and polarizer at a different angle, and it isn't compatible with the
> diffuser. It dimms the pixels and darkens the background. It isn't bad
> on some calcs, but it gets fairly annoying on others. Austin butler had
> a "dim" calc, but he got it and said it took a while to get used to, but
> that it wasn't too bad. All I can say is you can try. The problem is it
> it is a dim one and you decide not to do it, it is nearly impossible to
> put the mirror back on without looking VERY strange. It will have air
> bubles and dust, no mater how you replace it. If you like you can try
> with just the corner, but my experience shows that if the mirror is a
> piece of thick plastic and the one that doesn't work as well (It works,
> just dimmer pixels when the light is off) is a very flexible piece of
> plastic foil. You'll know by pulling the corner off. If it is thick, go
> for it. if it is thin, you may want to think about it. Try it if you get
> a panel. I charge $40 for the whole job (it has to cover the cost of the
> LCD panel I took apart). I got it from ALL electronics, but they
> nolonger sell it, so it is kindof my last priority. I have enough for 4
> calcs, and will need 2 or three for myself, so you, austin, and I could
> end up being the only person with these backlights unless someone had
> the misfortune of ordering the wrong LCD or thinking they could use it,
> but couldn't. I was on an LCD list before, so maybe I can purchase some.
> It would be best to find a black ON white backlit screen. It would look
> better, but I havn't found one yet.
>
> If you want it done, I can do it for you. I could send the piece (fit it
> to my 82 first) but It is difficult and requires patience. I have taken
> over half an hour just cutting the screen off, cause you obviously can't
> crack it, and you can't cut those plastic ribbon wires. Tell me what you
> want to do. I'll do my TI-82 before I do your TI-82, just to see if it
> works well!
>
> Respond soon!
>
> Richard Piotter
>
> E-Mail:
> richfiles1@hotmail.com
> richfiles@usa.net
>
> The Richfiles:
> <A
> HREF="http://www.geocities.com/SiliconValley/Lakes/5081/Richfiles.html">The
> Richfiles TI Page</A>
> <A HREF="http://www.geocities.com/Area51/Lair/8510/Richfiles.html">The
> Richfiles Model Building Page</A>
>
> ______________________________________________________
> Get Your Private, Free Email at http://www.hotmail.com
References: